The best DACs for Apple Music Lossless in 2025

Fiio’s affordable KA11 dongle contains a DAC with a maximum resolution of 32bit/384kHz — which is well above Apple Music’s top-tier “Hi-Res” lossless format (24bit/192kHz) — so you can be sure that you’re getting every last bit of quality out of whatever you’re listening to. Best of all, the KA11 is powerful, too, with a higher volume output than Apple’s on headphone adapter (more on this below). At around $30, this dongle is the best bang for your buck when it comes to upgrading the audio experience on your iPhone, Android, PC or Mac. There’s even a Lightning version available for those with older iPhones and iPads.

We particularly like the simplicity of Fiio’s KA11 as it’s plug-and-play with no need to charge it. It’s only slightly bigger than a typical headphone adapter and it comes with a rugged, woven cable, so it can handle a lot of wear and tear. There’s even a small LED on the front that lets you know if you’re listening to standard, high, or higher-resolution files so you can be confident you’re getting the most out of your music in real time.

Yes, it’s the Apple headphone adapter you know and (maybe) love, but it’s worth considering if you want something super lightweight and even more affordable. Apple’s dongle doesn’t support the larger, Hi-Res files available on its music service, but it can handle the standard lossless (24bit/48kHz) format no problem. As you’d expect, it’s available in Lightning and USB-C versions depending on which Apple device you’re connecting it to.

Sure, the most demanding listeners might lament the lack of support for the higher resolutions, and it can be a little quiet with some headphones that are high impedance (typically more expensive “audiophile” models). For the vast majority of users, though, Apple’s dongle will do the job. If you’re not sure, check the manual for your headphones and look for Impedance (often listed as Ohms) — anything below around 150Ohms and you should be fine. Anything above that, and you might want to consider Fiio’s dongle instead.

While this guide is primarily focused on Apple Music, most of the gear here will unlock lossless audio no matter where you listen. If Tidal is your platform of choice, you might be familiar with the MQA codec, which the company used for its high-resolution audio until eventually switching to FLAC in 2024. MQA might not be as common in streaming anymore, but if you still want to make sure you can listen to music from stores or services that provide it, the iFi GO Link will have you covered, along with the standard Apple Music high resolution audio formats, and anything else, up to 32-bit/384kHz.

Sennheiser’s BTD700 is a wireless adapter that plugs into your phone, upgrading its Bluetooth capabilities with the latest high-resolution codecs such as Aptx Adaptive and Aptx Lossless. iPhones don’t support any of these natively, but with this small dongle, you can unlock the full potential of Bluetooth audio and the higher bitrates (and in theory audio quality) Aptx Lossless offers. There’s a small caveat, though: you will need Bluetooth headphones that also support one of these codecs such as these or these (or check the product page of the set you own or are considering).

The BTD700 is simple to use, just plug it in to your phone’s (or other device’s) USB-C port, pair your headphones to it and off you go. An LED on the dongle lets you know which of the six different Bluetooth “qualities” (codecs) you’re enjoying so you will know when you’re listening to lossless audio. The handy part? Once you’ve paired your headphones with the dongle, you won’t need to re-pair if you connect the BTD700 to a PC or Mac. This little adapter effectively gives anything with a USB-C port an audio upgrade, and there’s even a low-latency mode for gaming. Note, there’s no Lightning option here, so if you’re on an older phone you might have to live with using an adapter.

If you’re looking to take things to the next level without spending “high-end” money, there’s a lot to love about the Melody DAC from Snowsky. Unlike a simple dongle, the Melody has onboard controls and two headphone jacks. One of those is for regular 3.5mm headphones, but the other is for 4.4mm “balanced” headphones, which means the Melody can grow with you if your audio journey takes you deeper into the world of audiophilia.

The wood finish gives it a classy feel and although it’s light, it still delivers that quality “Hi-Fi” feel. As for sound quality, there’s support for 384K/32bit sample rates, which covers everything Apple Music can deliver. The built-in amplifier can easily go louder than you should probably ever listen and there are other luxuries, too, such as support for inline microphones — so you can still handle calls and take meetings on your phone. We also love that you can tailor the sound to your preference via the Fiio Control companion app.

While you can squeeze an impressive amount of audio tech into a headphone adapter, a slightly bigger device affords a decent step up in both specs and features. Moondrop’s Moonriver T2i DAC is slightly larger than a pack of gum, and it has a stylish design that doesn’t look like a boring, generic dongle.

Importantly, the Moonriver T2i builds on the success of the company’s Moonriver 2 DAC. The “2” partly refers to the use of dual DAC chips here, which delivers a “balanced” signal. Each channel can handle up to 32bit/384KHz resolution and there are two headphone ports. One for standard 3.5mm headphones and another for 4.4mm connections — making use of that balanced output. If this is your first step into the world of Hi-Fi DACs, you’re totally fine with 3.5mm headphones, but some prefer the 4.4mm connector as it provides more power and potential signal benefits, especially if you’re using a headphone amp.

With the Moonriver T2i you have a couple more practical advantages. For one, there are physical volume controls on the device itself. If you ever felt that the 16 levels of loudness on the iPhone (I just counted) weren’t enough, then the 100 steps of adjustment on the Moonriver T2i (via companion software) eliminate any worries about setting the music to the perfect level. If your headphones have an in-line microphone, the good news is that this dongle will pass that through to your phone or PC so you won’t need a separate device for calls.

Most importantly, the sound that comes out of the Moonriver T2i is bright and bold. You’ll hear audiophiles talk about sound stage, detail and width, all you need to know is that this DAC ticks off all the buzzwords and serves up bright, robust sound that’s going to make any lossless/hi-res music really shine.

Who said a DAC needs to be a dongle? If you’re looking for something a little more all-in-one then the SP3 BT active speakers from Fiio are a great option. We like that, for the same price as many standalone DACs, you have everything you need to decode high-resolution music from almost any source with USB-C and Aux inputs for phones along with standard Hi-Fi connections such as optical, RCA and coaxial.

These speakers didn’t make it to our testing bench, but the SP3 BTs regularly receive praise for their sound and premium build quality at a reasonable price. For Bluetooth listening, there’s support for both Aptx Adaptive and HD along with Sony’s rival LDAC making these speakers something of an audio swiss-army knife. While these speakers will make a perfect companion to your home office or workspace, they can easily find a home in your living room or den connecting to any other music players you might have (for vinyl you’ll still need a pre-amp).

If you’ve had some experience with DACs and are looking to ratchet things up a notch or three, then the Mojo 2 from British company Chord wants to have a word. At $650, this is definitely in the high-end price range, but the experience and features it offers make it worth considering for serious audiophiles. But the brains behind the Mojo 2 have been making digital to analog converters pretty much since there was digital music to even convert. That experience is what makes the Mojo 2 a favorite among music fans.

Most options in this guide are designed for mobile devices first, the Mojo 2 is more of a hybrid device. The mobile dongles above all take their power from the player you connect them to, which is convenient, but obviously is less kind to your phone’s battery life. The Mojo 2 has an internal cell so won’t tax the one in your phone or laptop. It’s small enough to be portable, but substantial enough to live on your desk.

Unlike most DACs that use off the shelf chips to handle the digital-to-audio conversion, the Mojo 2 uses field programmable gate array (FPGA) technology to create its own custom “chip.” It’s also powerful enough to act as both a DAC and a preamp, driving even power-hungry headphones with ease. We’ve seen FPGA gain popularity in gaming circles for its ability to imitate various consoles, but that same flexibility is what makes it interesting to the audio engineers at Chord.

If you need something that’s capital L loud, then the Mojo 2 will not disappoint. Proceed with caution here. It’s actually powerful enough to drive two pairs of headphones at the same time and has two 3.5mm ports so you can do exactly that. The curious circular buttons can also be used to change sound profiles with an excruciating level of detail.

The Mojo 2 has standard USB-C, microUSB, optical and coax inputs so it’s more flexible than a lot of its competition in this regard. Although it’s worth noting that you can only charge the Mojo 2 via microUSB. Of course, there’s a cable provided for this, but if you’ve fully made the switch to USB-C, it’ll mean you have to guard the charging cable closely.